Ready mode wont enable

Question

2015 Mitsubishi Lancer Evolution (manual trans). Using an EVO-ONE, I checked all wires and made sure everything was correct the only thing I didnt connect was the motion sensor, I cannot seem to find it in the driver side footwell unless the plug has been changed in later year models. Anyway when trying to remote start the parking lights flash three times, indicating ready mode is not enabled. I have tried all 3 different ways as described in the installation instructions but still does not work.

Answer 1

I changed some stuff around on the flashlink manager. Changed to 33.2, now when I turn the key off the car keeps running until I get out and close the door; which I don't like. Try the 3x oem remote start and car just cranks and doesn't start, then parking lights flash 4 times which means it doesn't detect a tach signal.

Comments

What is the S/N to the module?

---

002807 242478

---

I would think it's only cranking bcause the module currently does not have a valid dcryptor inside it. It has also been maxed out on dcryptor attempts. I will get it reset for you, it will be ready for use in 24 hours. Reprogram the module in the vehicle and then re send the dcryptor. Once completed, test it.

---

Ok, so I reprogrammed and tried it. First crank did not start, second it did! But when I got in the car I could not turn the key as it is keyless entry (FAST Key), tried pushing in the clutch and nothing, pushed on brake pedal and car shut off and then was able to turn key. Also is there a way to make the car turn off when I turn the key off? or does it have to run until I close the door?

---

It will shut down on door close.

 

Also for the tumbler did you cut the wrie as shown in the guide? This is what allos the tumbler to turn once you enter.

---

Yes I cut the wire as shown. Can turn the key as normal just not when remote started.

---

try firmware 74.22 and tell me if the tumbler turns during take over.

---

Newest firmware it lets me update to is 68.03

---

We arent looking for the newest, we want to roll it back. If you scroll down the firmwares in the bypass are you able to select 74.22?

---

Yes I was able to rollback the firmware to 74.22, going to test it now.

Here is my options selected, should I change any?

Bypass (74.22):

A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, B1, C1, D2

Remote Starter (1.25):

3.1, 4.1, 6.1, 7.1, 8.1, 9.1, 10.1, 11.1, 11.4, 12.1, 13.2, 14.1, 15.1, 16.5, 18.1, 19.1, 20.6, 21.1, 24.1, 26.1, 29.1, 30.1, 31.6, 32.1, 33.2, 34.2, 35.1, 36.3, 37.1, 38.2, 39.1

---

Now it just cranks, will not start.

---

yes, because you need to re program it once you roll the version back.

---

oh ok. Do I have to do another decryption too?

---

with firmware 74.22 you should not even need dcryptor.

 

youll turn the key on, blue will flash, turn key off and it should go out.

---

Car starts now but again when I enter key doesn't turn. I know that the wires at hooked up correctly because if I don't put the plugs into the module, the key will not turn and when I put them in the key will turn. I may just change the settings so it will turn off when I open the door.

---

You can always set it to shut down on door open.

 

With the red connector unplugged, you should be able to turn the knob. The interupt we do is for the power that goes to the solenoid which prevents the solenoid from locking the knob. You might wanna look at that connection if it doesnt turn with the red unplugged.

---

That must be the problem then. I unplug the red connecter and the key won't turn. I'm pretty sure its connected properly, I will double check later. The only thing I don't have connected is the motion sensor, I could not find that plug.

---

Just checked wiring and made sure the wires were in the right place in the plug. Everything was correct.

---

Try firmware 86.02 perhaps? Reset, re program.

I know it had a change made for the mitsbusihi fast keyless system.

 

Aside from that since I can't see your installation, I suggest door open shut down.