Fortin EVO-ALL couldn't synchronise with Crime Stopper SP-502

Question

 

Hi , 

 

i have followed the guide for mitsubishi eclipse cross. after completed the decrytor process. ( with sugguested setting loaded)

 

notice the following function can't work out.

 

1) when the remote start(3x lock) is activated , the dashboard promote out a error promote "electrical system service require " 

 

2) the evo-all can't able to synchronise with crimestopper sp-502 , both of the device doesnt tele the event. (example when activate/press OEM remote lock , the crime stopper remote doesn't display lock )

 

Answer 1

Turn off D1 since you are not doing a Stand Alone installation.

 

1) when the remote start(3x lock) is activated , the dashboard promote out a error promote "electrical system service require " 

This message should disapear after takeover. It may show once every so often since the car is not started by a human.

 

2) the evo-all can't able to synchronise with crimestopper sp-502 , both of the device doesnt tele the event. (example when activate/press OEM remote lock , the crime stopper remote doesn't display lock )

You will need to check with Crimestopper if this feature is available. As long as C1 is enabled in the EVO, we send out the oem remote commands through datalink. It is up to the crimestopper to manage it at that point. Typically 2 way remotes only receive confirmation when it is that exact 2-way remote that initially sent the command. Which is not the case if you are locking with the oem remote ..

Comments

I've installed a evo all with sp502 you need to turn off D1 and on the crime stopper turn option 5 to button 3 and they should sync

---

Hi Robb,

 

1) when the remote start(3x lock) is activated , the dashboard promote out a error promote "electrical system service require " 

This message should disapear after takeover. It may show once every so often since the car is not started by a human.

the engine wont even start up with the error message display.

in such case, do Fortin disable the immobilizer for the OEM alarm system ? I have tried by putting the OEM remote away from the vehicle and use crimestopper alarm to start up. And display shows require OEM remote in order to start engine.

at this point of time , i am quite confuse with and without fortin evo-all , what is the feature that can benefit my current setup.

- i cant remote start

- i cant link up with crimestopper alarm

- any improvement in security ?

 

---

Hi Mike,

I've installed a evo all with sp502 you need to turn off D1 and on the crime stopper turn option 5 to button 3 and they should sync.

I dont understand the part on crimestopper turn option 5 to button 3.

can you able to explain in details ?

thanks in advance

---

EVO-ALL is a transponder bypass module to allow your crimestopper to properly remote start the vehicle. WIthout a transponder bypass module, your car will never remote start.

The EVO-ALL will also communicate certain CAN-BUS vehicle statuses to the crimestopper.

 

Currently, you cannot remote start because settings in the evo-all are wrong. You need to turn off option D1.

---

Change the crime stopper setting that it recognises 3x lock (its setting number 5 option 3)

---

Hi Mike,

I dont get what you mean by Setting Number 5 Option 3?

Is it H Option and turn on H3 ?

the setting at Fortin Evo-all or CrimeStopper ?

---

Hi Robb, I have change the setting to D1 off but it seem like crimestopper sp502 cant synchronise the feature.

---

I dont get what you mean by Setting Number 5 Option 3?

He is talking about the remote starter option. It is NOT in the EVO. It is part of the SP502 options menu. 

 

Have you considered simply having the system installed by a local shop familiar with these products?

---

There is no local shop i know in singapore that is fimilar with this

---

Ok, CrimeStopper sp502 is program and  synchronise the lock and unlock , it receive the signal from the Fortin Evo all

 

now left with remote start issue from Fortin evoall , please advice