Questions & Answers

Crank but wont start

0 votes

This is 2013 Toyota Camry G Key. Bypass Version 79.37 and Remote Starter version 1.19.

Bypass version a1 to a11 is on. Rest all are off.

When i try to start the car using Remote, Vehicle crank but wont start. Parking light flashes 4 times. This means Tach signal is not obtained properly from Can bus. 

I see sometimes, car Starts and since Tach signal is not obtained properly the starter disengages slowly.

Sometimes it crank and it wont start.  Please advise how to solve the problem. I am using fortin RF642W

remote and the remote are configured with no issues.

 

I have verified Can high, Can Low and IMMO data from where i tapped to the wiring harness of EVo one, i see good continuity. 

Issue 2: My OEM remote is not working. I enabled 3 times lock on remote and bypass but still not working. Not a major issue. but dont know why it is not working. PLEASE NOTE i have enabled 3xlock on remote start and oem remote monitoring on bypass, but still it doesnt work.

Issue 3: After i remote start the car(when it work sometime) if i open the door(getting my hand inside the door and opening the door from inside), there is no alarm. I am thinking that if i lock the car with remote, and when car is remote started, then if i try to open from inside of the car, i expect car alarm to come on but notihing happend. Issue 2 and 3 are not high priority. but for sure issue 1 have to be addressed. I am happy to wire tach (hard wire). but dont know what to connect from where.. 

i have cross verified my 

here is my option for remote starter version 1.19.

 

39.1

38.1
37.1
36.2
35.1
33.1
34.1
32.1
31.1
30.1
29.1
26.1
25
24.1
21.1
20.6
19.1
18.1
16.5
15.1
14.1
13.2
12.1
11.1
11.4
11.3 off
9.1
4.1
6.1
7.1
8.1
2.4
1

 

 

 

asked Jun 23, 2016 in Toyota by sivaraj palanisamy (250 points)

1 Answer

0 votes

1. 3xlock is not supported on your year model of the Camry, only PTS models supported oem remote monitoring, you will need an aftermarket RF kit.

 

2. Looking at your service number here : http://ca.fortin.ca/en/support/002b07100333/ it looks like either you toggled while the evo one unit was still plugged into the flashlink updater or saving the options failed or the unit got disconnected, as you can see, the options are not properly being displayed,  I would take the evo back to the computer, make sure you are in connection mode:remote starter on the bottom right side of your screen before you even plug in the evo-one unit to the flashlink updater, please re-flash the firmware in the remote starter side and check your options afterwards.

3. the parking light diagnostics is telling you "tach issue" simply because the vehicle never fully started and ran, so no tach signal was detected.  Your issue lies elsewhere, a no tach issue would be, the vehicle starts and runs but the actual vehicle starter will overcrank (stays on grinding)

 

 

 

Thank you

answered Jun 23, 2016 by J M (64,060 points)
hi, the issue is resolved now. can u please advise three more questions.

 

1) How do i reset bypass alone in remote starter. I was told that press the program button then add main connector, when led is red and solid release , then press and hold until all led blink then release... This will rese the BYPASS is that right?.

If so where it is documented?..

2) When I do Master Reset, do i need to relfash?.

3) How do i program remote starter in car without Flash link updated to option Function 2 and option 4. Please advise.

4) My car OEM remote doesnt work to lock/unlock when my car is remote started.

"1) This will rese the BYPASS is that right?." Correct hold programming button insert power connecter, let go on red, hold down button again till led's cycle and unplug. This will erase any programming and also set the options back to default as long as settings protection isnt on in the bypass side of the module.

 

"2) When I do Master Reset, do i need to relfash?." No but you will need to re program and also re enable any specific options needed.

 

"3) How do i program remote starter in car without Flash link updated to option Function 2 and option 4. Please advise." If you do not have the flash link then this will have to be done using the valet switch and a RF remote and anetnna just as it is shown in your quick installation guide.

 

"4) My car OEM remote doesnt work to lock/unlock when my car is remote started." If this is the case i would take a look at the doorlock data wire connection you had to make in the vehicle, something is wrong there.

 

4) My car OEM remote doesnt work to lock/unlock when my car is remote started.

Start your vehicle with the key (regular start not a remote start), then try pressing lock or unlock on the oem remote. If you cannot lock or unlock while the engine is running his way, you will not be able to lock or unlock while the car is remote started.

 

I would suggest an RF-KIT for this vehicle as it is not listed as 3x Lock Start/Stop compatible on the fortin website. 

Robert,

 

I can lock and unlock using OEM remote using Regular Start. However it is not working when i do a Remote Start.

 

Please  advise.

You can actually try downgrading the bypass firmware and reprogramming it to see if anything changes but.....

As mentionned,

I would suggest an RF-KIT for this vehicle as it is not listed as 3x Lock Start/Stop compatible on the fortin website.

We do not have this vehicle listed as compatible with 3xlock start most likely because the remote does not function while the vehicle is under remote start. We do not list vehicles that either we do not detect the remote or the remote seizes to work once remote started; this is why an RF-KIT is also listed as a Required Technology.

 

I invite you to visit the fortin.ca Toyota Camry compatible solutions page as it shows available features and any required parts.  https://fortin.ca/en/vehicles/toyota/camry/2013-g-key/

Robert,

https://fortin.ca/en/vehicles/toyota/camry/2013-g-key/

I visited the above URL for 2013 toyota camry g key. it does say it support 3x remote start.. however u r saying that it is applicable only for PTS model.. 

pls advise where did u find that info.

also u saved me before while trying to program using valet key and find out the issue. please provide me ur email id pls again..

...